Waldorf, Maryland
Kenmore Appliance Service in Waldorf, Maryland, with the published national price range up front, the failed part confirmed by testing on site, and the repair price stated before any work begins.
A Kenmore badge tells you where the appliance was sold, not who built it. For decades, Sears put the Kenmore name on machines from several different factories, which means two Kenmore refrigerators of the same age can share almost no parts at all. We service Kenmore refrigerators, washers, dryers, dishwashers, and ranges across Waldorf, and every job starts with the model number, because its first digits identify the company that actually built your machine.
Kenmore model numbers open with a three digit prefix, and that prefix codes for the original builder. One prefix points to a machine built by Whirlpool, another to one built by LG, another to a Frigidaire-built unit, and so on through both lines. The badge stayed the same while the builders changed underneath it, so a repair path written for one Kenmore will not fit another until the prefix is read.
This is more than trivia. The prefix decides which pump, board, motor, or element your machine takes, how its panels come apart, and which failure patterns are common to it. Include the full model number in the quote form, and we arrive knowing which machine we are coming to repair.
A Kenmore French door refrigerator in a Bannister home was holding the freezer near zero while the fresh food side drifted into the mid-forties. The model number's prefix identified the machine as LG-built, which pointed testing at that platform's fan layout. The condenser fan motor had failed, so heat was not leaving the system and the compressor ran long to compensate. We replaced the motor with the part matched to that platform, cleaned the condenser coils, and confirmed temperatures falling in both sections before finishing.
Because Kenmore machines were built by several companies, cost follows the appliance type and the platform underneath, not the badge. No Waldorf shop publishes a local price list, so we publish the national ranges openly. From Angi's 2026 data: refrigerator repair runs $200 to $300 nationally, washer repair $50 to $450, dryer repair $100 to $400, and oven and range repair $100 to $500. Across all appliances, the average repair is about $170 nationally, with most jobs between $100 and $240. We state the figure for your machine once testing confirms the failed part.
Start with the quote form at the bottom of this page, and include the full model number if you can — on a Kenmore it is the most useful thing you can send. We read the prefix to identify the builder and parts family, then on site we test the failing system and confirm the component at fault before anything is replaced. Parts go in matched by part number to the platform that built your machine, and the job ends with a full cycle or cooling check.
Use the quote form at the bottom of this page. Tell us which Kenmore appliance is down and what it is doing, and add the full model number from the label if you can find it — the prefix tells us who built your machine. We will respond with the published range for your repair and the next step.
One of several manufacturers, depending on the model. Kenmore was a store brand, built by companies including Whirlpool, LG, and Frigidaire. The model number's first three digits are the prefix identifying the builder, and it decides the parts and repair path.
Published national ranges from Angi put refrigerator repair at $200 to $300, washer repair at $50 to $450, dryer repair at $100 to $400, and oven and range repair at $100 to $500, with repairs overall averaging about $170. Your figure depends on the appliance and failed part, and we state it after testing confirms the fault.
Look inside the door or on the door frame first — that is where most refrigerator, dishwasher, and washer labels sit. Dryers often carry it inside the door opening, ranges behind the storage drawer. Send us the whole string, prefix included.
In most cases, yes, because the parts belong to the company that built the machine, and those parts families stayed in production across many models. Reading the prefix makes the search fast. When a part for a genuinely old model has been discontinued, we tell you plainly and talk through the repair-versus-replace math.
Because the badge and the builder are different things. A Kenmore washer from one builder has a different pump, drive, and control layout than one from another, even in the same model year. That is normal for this brand, and exactly why we identify the builder before diagnosing.
Most single fault repairs take about one to two hours on site once the part is confirmed. If your machine's platform needs a part ordered in, we give you the timing up front, plus how to use or rest the appliance safely until it arrives.
Tell us which appliance is down and what it is doing. We read every request that comes in and respond with the published national range for that kind of repair and the next step, starting with a visit to test and confirm the failed part on site.
Prefer to talk it through first? Send the form and we will call you back at the number you give us.